Edgebander/used Brandt KDF 350C 2006god

Automatic edge banding machine for prikladyvaya in the right-hand version for working on the glue-melt.
Operations performed: pre-jointing edges of the workpiece, gluing, trimming, milling of overhangs, rounded corners (contour milling), scraping, polishing.
Attaching a node to work on the glue-melt granules. The tank hot melt adhesive is the adhesive under the video. Apply the adhesive to detail with glue roller rotating in the direction and against the direction feed. Electronic regulation of the temperature in the adhesive tank. Automatic reduction of temperature in the reservoir to prevent overheating of the adhesive.
Contact the heating plate for preheating of the workpiece, to ensure high quality gluing.
Auto shop for roll-and strip material, incl. a device for cutting roll and a plate for bale diameter 800 mm.
Area of pressure from the main pressure roller with pneumatic drive, and also with the special roller clamp for extra sealing the upper and lower joints.
Adjustable Central mechanism of the upper clamp.
Central manual chain conveyor lubrication.
Planer-type milling unit (motor 2 x 2,2 kW, 200 cycles) for butt joint before fining a part of, vertical reset using spindle, electro-pneumatic control horizontal direction, 2 motors (1 works in the direction of flow and against 1 flow direction). The unit is equipped with 2 diamond jointing cutter head diameter 100 x 48 x 30 mm, Z=3+3, key 8 x 3 mm. Maximum allowance for processing 3mm.
End trimming unit (2 motor 0.18 kW, 200 Hz, 12.000 rpm.min.) removing the front and rear overhangs cladding material. Precision linear guideway.
Pulling compound miter cuts to achieve high precision.
The range of tilting facing straight to the chamfer 0 – 150.
2 mitre saws with a diameter of 100 x 2.6 x 32 mm, Z = 30.
Pneumatic 2-position permutation of the trimming Assembly for installation provisions chamfer/straight.
Milling unit (2 motor 0,27 kW, 200 Hz, 12.000 rpm.min) for pre-milling on the thickness of the shield at the top and bottom with vertical and horizontal feeling of the part.
2 combined cutters 56/50 x 16 x 16 mm, Z = 4, with interchangeable plates for milling with radius r=3 or in a straight line.
Pneumatic 2-position permutation of the milling machine.
Unit profile milling top and bottom for profile milling corners of parts with edges post - and softforming and fillets the angles of the edges of PVC. Processing of edging material from massive wood possible under certain conditions, is required the preliminary tests.
1 motor 0,35 kW, 200 Hz, 12 000 rpm.min.
The thickness of the edge material max. 3 mm (radius).
Standard 2 radius of the indexable insert r = 3 mm, diameter 73/61 x 16 x 16 mm, Z = 3.
Scraping unit for PVC edges (No. 5736)
Feeling the top, bottom and sides, chamfering and rounding pre-milled PVC edges. The thickness of the edge material max. mm 3, profile knife r = 3 mm.
Pneumatic permutation scraping unit for discharging/connection to the working area.
Buffing unit with 2 motors (No. 5455)
to soften the edges top and bottom. 2 motor 0,09 kW, suspended separately and adjust the tilt and height. 2 cloth disk Molton diameter 120 x 20 mm.
Static frequency inverter 200 Hz.
Electronic braking of the motors for trimming and milling units.
Support for styling detail extends to 350 mm.
Noise-protective casing with a Central nozzle with a diameter of 100 mm for connecting the suction nozzles with a diameter of 120 mm chip removal from the planer and the milling machine.
Electronic control PC16
The BRANDT control system with color graphic monitor for easy management and programming.