Automatic furnace for gas burners MMI 962.1 mod 23
Offer type: salePublished: 18.03.2016
| Price: | negotiated |
| Company: | TD Favorit |
| Seller: |  menedzher |
| Phones: |  0505020019 Show phone |
| Address: | Ukraine, Kyiv |
Automatic furnace for gas burners MMI 962.1 mod 23
For gas burners with boosting
Terminals for servo dampers
Built-in remote restart
Possible flame sensor:
- Ionization probe
- Infrared sensor
Furnace machine for MMI 962.1 gas burner operates and control gas and
combined burners of any nominal charging power (tested and approved as per EN 298).
If the connected servo dampers, 2-stage operation with two fuel valves or a modulating one fuel valve. Different designations of types and models identify automatic burner according to time intervals, and in accordance with national standards.
Furnace machine MMI 962.1 Mod. 23 can be used as a replacement MMI 812 Mod. 23 or MMI 812.1 Mod. 23.
Design features
Furnace machine protected by fire-resistant transparent plastic housing with plug connection and comprising:
- Synchronous motor with gear speed reducer as the drive for Cam switch
- Cam switch with informative colour indicator software - 12-pin Cam drive controlling program flow
- Circuit Board with electronic components On the front panel of the furnace of the machine there are the following important indicators and operating elements:
- The reset button with integrated signal lamp to indicate fault - Coloured program indicator - Central screw fastening
Technical data
Operating voltage 220 / 240 V (-15...+10%) 50 Hz
The deviation of the oscillation frequency of alternating current result in proportional timing
The guard at the entrance 10 A fast, 6 A with delay
Power consumption: approximately 10 VA
Maximum load on terminal:
- TC. 3 2.0 A, cosφ 0.2
- TC. 4, B 2.0 A, cosφ 0.4
- TC. 5, 6, C 1.0 A, cosφ 0.4
Only 5.0 A, cosφ 0.4
Sensitivity 1.0 a
The minimum required ionization current 5.0 a
The cable of the flame sensor 20 m max.
The air pressure switch working contact 4.0 A, 230 V
Waiting cause no
The flame sensors
- ionization probe
- infrared detector IRD 1020.1
Weight including plinth 350 g
Installation position in any
Protection class IP 44
Permissible climatic conditions for the device and the flame sensor max. humidity 95% at 30ºC
The permissible temperature range
- Operation-20ºC ... +60ºC
- Storage -20ºC ... +80ºC
The formation of ice, water and condensation are not allowed
Code, combined with led. according to EN 298 BTLLXN
For gas burners with boosting
Terminals for servo dampers
Built-in remote restart
Possible flame sensor:
- Ionization probe
- Infrared sensor
Furnace machine for MMI 962.1 gas burner operates and control gas and
combined burners of any nominal charging power (tested and approved as per EN 298).
If the connected servo dampers, 2-stage operation with two fuel valves or a modulating one fuel valve. Different designations of types and models identify automatic burner according to time intervals, and in accordance with national standards.
Furnace machine MMI 962.1 Mod. 23 can be used as a replacement MMI 812 Mod. 23 or MMI 812.1 Mod. 23.
Design features
Furnace machine protected by fire-resistant transparent plastic housing with plug connection and comprising:
- Synchronous motor with gear speed reducer as the drive for Cam switch
- Cam switch with informative colour indicator software - 12-pin Cam drive controlling program flow
- Circuit Board with electronic components On the front panel of the furnace of the machine there are the following important indicators and operating elements:
- The reset button with integrated signal lamp to indicate fault - Coloured program indicator - Central screw fastening
Technical data
Operating voltage 220 / 240 V (-15...+10%) 50 Hz
The deviation of the oscillation frequency of alternating current result in proportional timing
The guard at the entrance 10 A fast, 6 A with delay
Power consumption: approximately 10 VA
Maximum load on terminal:
- TC. 3 2.0 A, cosφ 0.2
- TC. 4, B 2.0 A, cosφ 0.4
- TC. 5, 6, C 1.0 A, cosφ 0.4
Only 5.0 A, cosφ 0.4
Sensitivity 1.0 a
The minimum required ionization current 5.0 a
The cable of the flame sensor 20 m max.
The air pressure switch working contact 4.0 A, 230 V
Waiting cause no
The flame sensors
- ionization probe
- infrared detector IRD 1020.1
Weight including plinth 350 g
Installation position in any
Protection class IP 44
Permissible climatic conditions for the device and the flame sensor max. humidity 95% at 30ºC
The permissible temperature range
- Operation-20ºC ... +60ºC
- Storage -20ºC ... +80ºC
The formation of ice, water and condensation are not allowed
Code, combined with led. according to EN 298 BTLLXN
