Vibrotek Machine For The Production Of Cinder Blocks!Ukraine.
Offer type: salePublished: 28.02.2015
| Price: | 4 000 UAH |
| Company: | ASVgroup |
| Seller: |  Lyisenko Aleksandr Sergeevich |
| Phones: |  +38(066)610-60-68 Show phone |
| Address: | Ukraine, Poltavs'ka Oblast', Kremenchuk |
Machines universal household for small-scale production: the Foundation blocks of size HH; sidewalk curb size HH; HH; HH; Machines can produce blocks of any filler,including: clay, limestone, small gravel, large gravel(with cross-section up to 75 mm), bricks, broken plaster, glass, slag, construction waste, waste concrete production, etc..Consumption of electricity for 8 hours 1.5 - 2 p, when the motor: 0,37 kW, 220 V, 2700 rpm Autonomous compactor can also be used for tamping soil and concrete(Foundation,Playground, etc..) If you type in a search string such as "buy a machine for the manufacture of cinder block" you will see that the cost,depending on the modification,is 11600-26850 RUB in Addition to other production related equipment: mortar mixers,spare parts, etc.
Produced at vibrolance wall blocks can be solid or hollow. For a rough understanding about the production of cinder blocks on the equipment we recommend you to look at the schema.
Full-bodied, have good strength properties and are often used for foundations and exterior cladding.
The vibrating presses for the production of blocks
Void provide good heat and sound insulation of walls. In addition, the voids in the blocks allow to reduce the consumption of raw materials and, as a consequence, the cost of production. When this strength characteristics satisfy all necessary requirements.
For the production of blocks used public construction materials: cement, sand and water.
As the filler used: slag, crushed stone, gravel, scrap bricks, scrap concrete products, construction wastes, sawdust, chips, shavings, clay, ash and more.
The use of fillers (mostly free) that allows you to not only significantly reduce the cost of products, but also to reduce the thermal conductivity and to improve the strength characteristics of the manufactured products.
Vibrotek "MARS"
Vibrotek "MARS" is a compact machine for making building blocks, designed for use in construction or personal use by private developers.
The feature of the machine MARS is the optimal ratio of price - performance - mobility. In our opinion this is the most practical machine series equipment for the production of blocks
The algorithm works on a cinder block machine “ MARS ”
Install the machine on a flat surface (preferably concrete floor);
To omit the matrix on the floor, lifting lifting lever and press the locking matrix limiter;
The second lever to raise the matrix with voids and to take her to the end position from themselves;
Made the dough in the mixer is quite hard (semi-dry) concrete. Water cement ratio not more than 0.5. Grade of concrete - 100 (and more). Preferably without clay and organic investments;
Loading the hopper of the machine (forms) with a small "hill". Preliminary vibroplate within 0.5 to 2.0 C. not more (depends on the humidity of the concrete)! When this pre-shrinkage (5-10%) of the concrete mixture and filling the form itself. Optionally, Stikovica concrete in the corners and other places. Excess concrete is cut and removed, the remains can be placed for receiving the front bar. For this you may use a specially made boot scoop or trowel;Buy vibrotek for blocks
Final vibroplate mixture for 15-30 seconds occurs with the upper clamping frame before their limiters;
To take two hands for lifting the lever and make the ascent of the matrix. Raising the matrix to produce with the included vibrator (vibration should be small);
After picking up the matrix, the terminator himself commits the matrix in the raised condition;
The unit is ready, and the machine moves to the rear wheels slightly lifting from the front shock absorbers for the handle, and is installed in the original position for making the next block.
Rules of operation:
To enable the machine to the network 220 with a grounded wire.
Time machine is running short (up to 2 minutes continuously).
The motor of the vibrator should not overheat.
Water (moisture) and the solution should not get on the on/off switch on the motor housing and the current-carrying wire.
After the operation, the machine must be cleaned, and wipe clean oil cloth surfaces.
PS-200 Machine for the production of wall block
Intended for the manufacture of wall blocks of different voidness based on a variety of fillers.
Production of blocks is carried out by semi-dry pressing.
The molding is made removable pallets, which reduces the production of space by stacking methods.
Enables the production of wall blocks with accurate geometrical dimensions, stable characteristics of density, strength, frost resistance and water absorption.
Provides excellent quality products due to the vibrators that provide uniform compaction of the sand.
Removable molds allow producing wall blocks of different shapes and sizes.
Performance from 1100 pieces per shift is due to prob
