Burning machine of Riello Mg 569
Offer type: salePublished: 22.04.2016
| Price: | negotiated |
| Company: | TD Favorit |
| Seller: |  menedzher |
| Phones: |  0506033570 Show phone |
| Address: | Ukraine, Kyiv |
AUTOMATIC COMBUSTION 569 MG RIELLO GULLIVER BS
Reset button lock (reset) – ensure burner unlock and activate various additional functions. Multicolor led – the main element of the indication. Both elements are located under a transparent cover reset button lock, as shown in the figure below. New automatic combustion MG569 On all gas burners GULLIVER BS (single-stage) and BSD (two-stage) there will be a new digital automatic combustion MG569.
New features New automatic combustion has many advantages compared to the machines of the old type : Long ignition (within safe time), the spark is generated only during the safe time of ignition of Series Gulliver BS - MG569 the Cycle of burner ignition
The adjustable air blowing after you turn off the Purge after shutdown – this feature ensures operation of the blower for some time after the extinction of the torch. The purge time after shutdown can be set from 1 to 6 minutes. This function can be set by pressing several times on the unlock button. After 5 seconds the indicator will automatically display a preset number of minutes by blinking the red led (1 pulse = 1 min purge after shutdown). If during the purge after shutdown will go a new request for heat, the purge is terminated and a new working cycle. Factory setting of the automatic firing device : 0 minutes = no purge after shutdown. Gulliver BS series - MG569 New features
Remote reset Feature the Remote reset enables you to restart the machine burning in the distance. The burner comes with a special connector to connect the remote restart button after locking. Link length should not exceed 20 m Gulliver BS Series - MG569 New features max 20 m connector connecting wire
Self-test a New automatic firing device has a diagnostic function which via a system of flashing signal displays the operating status of the burner or the cause of the problem. Gulliver BS series - MG569 New features Operating state of the burner can be identified by color coding, which is described in the table below.
Gulliver BS series - MG569 self-test If block occurs, the red light is on continuously. In this case, to display the cause of the problem, you must click reset lock (reset) and hold it for 3 seconds. The control panel generates a sequence of pulses that is repeated at intervals of 2 seconds. The number of pulses you can determine the type of error according to following table. See table of error codes Example of a pulse sequence
Gulliver BS series - self-diagnosis MG569 SEGNALAZIONE REASON 2 pulse At the end of the safe time, the flame is unstable: -Faulty ionisation electrode -Faulty or soiled gas valves -Reversed phase and neutral -Faulty ignition transformer -Poor burner configured (not enough gas). 3 pulse Relay minimum pressure of the air closes the contact or is closed before closed thermostat first-stage (marginal): -air pressure switch defective -air pressure switch badly adjusted 6 pulses of air Leakage with ventilation: -Leakage of air during pre-purging -air Leaks by blowing after turning off 7 pulses Loss of flame during operation: -Poor burner regulation (insufficient gas) -Gas valve defective or dirty -Short circuit of the ionization electrode to the ground.
Gulliver BS series - MG569 New functions other functions Automatic combustion allows to repeat the cycle (a complete repetition of the start of the program) in case of loss of flame during operation, a maximum of 3 attempts (if the flame is lost for the fourth time, it will lock). The new automatic combustion MG569 integrated filter against radio interference, so no more need to use 7-pin connector with filter. Saving of working parameters : - the reason for the last lockout - the total number of locks total number of hours of work (1st degree) All of these options can be reset manually.
Set for data exchange with PC Series Gulliver BS - MG569 you Can order a special kit to connect the machine torch to the PC; the computer will display the status of the burner, the number of working hours, type and number of issues, the serial number. This kit consists of fiber optic cable with PC & software CD for installation on your computer.
Gulliver BS series - MG569 Kit for PC data a Sample program for data exchange with PC
Ordering spare parts Series Gulliver BS - MG569 Installed on a New burner, automatic burning MG569 Spare parts New automatic combustion MG569 Old machine burning 568 569 RBL RBL RBL 566SE rev3 Old machine burning RBL 525SE/G 566SE RBL RBL RBL 566SE 566SE rev1 rev2 New automatic combustion MG569 +adapter
