Press for punching sheet metal up to 1.5 mm PML-60 STOCK

Press for punching sheet metal up to 1.5 mm PML-60 STOCK

  
The tool is a manual mechanism rattle
the type of driving the pin with a punch. In the dependent-
tis from modification of the tool, the piston can imagine
a whole tool (
the -60), or rotate
relative to its longitudinal axis (
the -60 is,
the -60).
- Drill in the processed metal sheet hole
the studs. For cutting holes with a diameter of 22 and 27.5 mm necessary
should pre-drilling diameter not less
10 mm under the pin of small diameter. For cutting holes
diameter 34, 43, 49 and 60 mm must be pre-
svarlivaya diameter 20 mm
- Remove the tool from the box.
- Screw in the working part of the piston rod, the corresponding
the selected diameter of the hole. Stiletto wrapped hundred-
party with fewer turns of thread.
- Tighten the stud with a wrench. Do not apply through-
measuring force when tightening.
- Put on the stud cylindrical spacer.
- Put on the pin matrix of the desired diameter.
- Holding hand matrix, insert the stud into the hole,
made in the sheet metal.
- Tighten the plug on the stud from the back side metal-
ski sheet.
- Rotating the handle around the head part of the tool set-
those cutting holes in sheet metal.
- Unscrew the plug and remove the cutting.
what is
- When using the tool, observe the industry and
production safety measures.
- During operation, observe the technical parameters.
The mismatch of the processed parameters of the metal technical
sian characteristics of the instrument will result in out
system.
Hydraulic press, PCs. . . . . . . . . . . . . . . . . . . . . . 1
Stud 19 mm, PCs.. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Stud 9.4 mm, PCs. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Plastic suitcases, pieces. . . . . . . . . . . . . . . . . . . . . . 1
Passport pieces. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Tips for perforation
round holes (matrix) 1 pc. mm. . . . . . 22,5
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28,5
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34,5
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43,2
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49,6
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61,5
The maximum thickness of the
machined metal, mm. . . . . . . . . . . . . . . . . 1,5
Weight, kg. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0,3