The steel boiler, pellet/wood burning TKAN1, 35 kW
Offer type: salePublished: 13.05.2015
| Price: | 79 000 UAH |
| Seller: |  Viktor |
| Phones: |  0961705734 Show phone0938114283 Show phone |
| Address: | Ukraine, Zhytomyrs'ka Oblast', Zhytomyr |
-
Brand:RADIJATOR INZENJERING DOOТип boiler:pellet/davanala power min./max., kW:20-themperature coolant max., °C:KG, %:aboone pressure, bar:rabochee pressure max., bar:4,5 Automation:in komplektaciya, V/Hz:230/Tiamat chimney, inch:abi (Height/Width/Depth), mm:1420/1170/885
-
Boiler TKAN developed by "Radijator Engineering" with the aim to offer the market the boiler, which according to its mechanical and thermal properties specifically designed for usetion of biomass as fuel.Using the generic term 'BIOMASS' is, of course, primarily refers to the use of pellets, however, it is also necessary to highlight the possibility of heating with the use of seed of fruit, especially the cherries. If the user wants to use any unspecified type of biomass, it must communicate with the servicedesign and development of the company "Radijator Engineering or a certified retailer, because very often certain types of biomass require specific solutions combustion. When using these fuelsmeans the automatic control of the main parameters. In all theseexamples of biomass use requires a certain degree of dryness of the fuel. With anotherhand, market demands are always aimed for maximum versatility fuel, so TKAN can be heated using wood fuel (wood, briquettes, etc.), and in thiscase load of fuel is carried out in manual mode.In this situation, the combustion process occurs with forced ventilation, so TKAN in these conditions is more effective than its predecessorswhich operate on the principle of free ventilation.Series boilers TKAN available in two variants: TKAN1 and TKAN2.TKAN1 covers a power range of 20-35 kW, and TKAN2 – 40-49,5 kW.
DesignIn appearance, the size of the furnace, the holes for the tabs on the fuel and cleaning TKAN retains all the positive characteristics of the previous models, thanks to which the company"Radijator Engineering is known in the market.Water part of the boiler, its method of heat exchange between flue gases and water, adaptedfor use of biomass and wood fuel. Due to the use of fans, i.e.forced ventilation, the path of the flue gases is longer compared to standard boilers. For the same reasons, perhaps the use of vortex generators to improvethe efficiency of the boiler.The efficiency of the boiler using pellets is more than 90%. With normal operating tempera-tour of the flue gas at the exit is about 120°C, and maximum modes – below 150°C.These values can be obtained on the display. During the formation of deposits of soot and ash on the heat exchanger of the boiler, which significantly impairsheat transfer and increases the temperature of the flue gases. If for a long time the boiler is not cleaned, the flue-gas temperature may be increased so that will halt operation of the boiler. Each equipment TKAN has a copper heat exchanger for connection thermoproteales valve. All elements of a water part of the boiler is made of seamless pipe brand ST 35.4 and sheet metal for boilers with a thickness of 4 mm and more, depending on the boiler capacity. Mark sheet Metall.0425 EU standard, or P265GH EUII standard.The combustion chamber has the following working principle: the fuel from the handling area flows vertically upward, that is, enters the combustion zone. The furnace is made of thick insulating materials and gray cast iron.Transportation of fuel is performed using the feed pellets. The fuel comesfrom the hopper with a volume of 240 l If necessary, very easy to disassemble the entire unit for threeindependent host: hopper, feeder and boiler.
