Universal divider grain APE-1M
Offer type: salePublished: 03.07.2013
| Seller: |  Labsnab Vasilij |
| Phones: |  (057) 703-55-75; (098)838-99-10 Show phone |
| Address: | Ukraine, Kharkivs'ka Oblast', Kharkiv |
The divider is designed for mixing and selection of representative sub-samples of cereals, legumes and oilseeds from the sample of no more than 8L one
Purpose and scope: the divider is designed for mixing and selection of representative sub-samples of cereals, legumes and oilseeds from the sample of no more than 8L one Hitch is allocated by the method of multiple Kvantovaya grain flow on consecutive separating and mixing sections.
The divisor used in laboratories serebryannyh, processing enterprises, research organizations, etc. Can be applied to granular or other engineering products in other industries.
The divider consists of two cone-shaped, two mixing, two divider sections and sections of the regulation in sample mass.
The product is poured into a hopper, depending on the mass of the sample, set on the Central limb of the socket at risk on the settlement division, according to the following table. After you lift the handle the valve stem, the product passes through the block partition separating the division of the flow of product into 4 parts, of which 2 parts are next on conic sections and 2 other parts through a window in the housing is discharged into the space between the inner surface of the housing and the outer surface of the section.
Section two cone structures are designed for blending and mixing of the product, in this case, the design of the cone with the vertex at the top, makes the distribution of the product (stretching) and the other with a truncated cone, the mixing. After selection of the sample must be weighed. If the weight is above or below required depends on the nature of the grain, it is necessary to change the position risks of pipe in the direction of increase or decrease values.
Advantages:
does not require special training of personnel;
easy installation of the divider in an upright position by adjusting the abutment screws;
the speed of obtaining sample accurate mass;
the use of the divisor for other bulk products.
Specifications:
The allocated sample, g
5.....300
Time allocation sample, with
10
Capacity hopper, l
8
Internal diameter, mm
150
Inner diameter section mm
85
Dimensions , mm
HH
Weight, kg, not more
20
Tel/Fax: (057) 703-55-75;
mob.: (098) 838-99-10 Basil;
mob.: (066) 737-48-19 Sergey;
mob.: (097) 000-51-14 Maxim.
Purpose and scope: the divider is designed for mixing and selection of representative sub-samples of cereals, legumes and oilseeds from the sample of no more than 8L one Hitch is allocated by the method of multiple Kvantovaya grain flow on consecutive separating and mixing sections.
The divisor used in laboratories serebryannyh, processing enterprises, research organizations, etc. Can be applied to granular or other engineering products in other industries.
The divider consists of two cone-shaped, two mixing, two divider sections and sections of the regulation in sample mass.
The product is poured into a hopper, depending on the mass of the sample, set on the Central limb of the socket at risk on the settlement division, according to the following table. After you lift the handle the valve stem, the product passes through the block partition separating the division of the flow of product into 4 parts, of which 2 parts are next on conic sections and 2 other parts through a window in the housing is discharged into the space between the inner surface of the housing and the outer surface of the section.
Section two cone structures are designed for blending and mixing of the product, in this case, the design of the cone with the vertex at the top, makes the distribution of the product (stretching) and the other with a truncated cone, the mixing. After selection of the sample must be weighed. If the weight is above or below required depends on the nature of the grain, it is necessary to change the position risks of pipe in the direction of increase or decrease values.
Advantages:
does not require special training of personnel;
easy installation of the divider in an upright position by adjusting the abutment screws;
the speed of obtaining sample accurate mass;
the use of the divisor for other bulk products.
Specifications:
The allocated sample, g
5.....300
Time allocation sample, with
10
Capacity hopper, l
8
Internal diameter, mm
150
Inner diameter section mm
85
Dimensions , mm
HH
Weight, kg, not more
20
Tel/Fax: (057) 703-55-75;
mob.: (098) 838-99-10 Basil;
mob.: (066) 737-48-19 Sergey;
mob.: (097) 000-51-14 Maxim.
