Sell edge banding machine KDF 340.
Offer type: salePublished: 27.07.2015
| Price: | 17 400 EUR |
| Seller: |  KMA Ukraina |
| Phones: |  0677941952 Show phone |
| Address: | Ukraine, Volyns'ka Oblast', Lutsk |
Edge Bander BRANDT KDF 340 Optimat
2005 V.
One-sided edge banding machine in right hand versions to work on the glue melt.
Fining for work on the surface of the melt granules. Processing of granulated melt polyurethane adhesive is possible provided always complying with the requirements and recommendations of manufacturers of glue.
Supply of glue under glue roller.
Apply the adhesive to the part using an adhesive roller, rotating in the direction or against the direction of flow and does not require installation on the thickness of the workpiece. Electronic regulation of the temperature in the adhesive tank, with automatic temperature reduction in the adhesive tank when you stop work.
Contact heating Shoe to pre-heat the edges of the workpiece.
Auto shop for coiled and strip material, incl. device for cutting of the roll and the plate roll edge material with a diameter of 800 mm.
Area of a clip with a main pressure roller with pneumatic actuator and a pressing roller without drive.
Input range with 3 positions for jointing: 1,- 2,- or 3 mm.
Central adjustable mechanism of the upper clamp, and Central manual lubrication of the chain conveyor.
The control panel at the entrance to the machine.
PLANER – MILLING UNIT 2 X 2.2 KW
for pre-jointing unit before fining a part of, vertical reset through spindle, electro – pneumatic control in the horizontal plane, 2 motor 200 Hz, (1 motor operates in the direction of flow, 1 against), max allowance for the processing of 3 mm.
Set of 2 diamond milling head 100 x 48 x 30 mm, Z = 3 +3, maximum workpiece thickness 42 mm.
END TRIMMING UNIT CHAMFER / STRAIGHT
for trimming the front and rear overhangs the edge with pulling compound miter cut for high precision.
The angle of tilt 0 to 15 degrees, 2 motor 0.18 kW, 200 Hz, 12000 rpm Equipped with 2 crosscut saws ø 100 x 32 x 2.6 mm, Z = 30.
MILLING UNIT 2 X 0,27 KW, 0 – 15 DEGREES.
for milling the upper and lower overhangs the edge against the direction of flow. 2 motors are arranged one after the other, with vertical and horizontal feeling. Permutation upper motor height with the mechanism of the upper clamp. Digital signs for quick changes.
The edge material thickness 3 mm max.
Workpiece thickness 8 – 50 mm
The angle of tilt 0 to 15 degrees
Standard two combined indexable insert diameter 56/50 x 12 x 16 mm, Z = 4, R=3.
SCRAPING UNIT
Feeling top, bottom and side. Chamfer or fillet pre-milled PVC edges. The maximum thickness of the edge material 3 mm. Permutation upper device height mechanism with the upper clamp. Set of 2 profile knife R = 3 mm.
BUFFING UNIT WITH 2 MOTORS ON 0,09 KW
to soften the edges of the top and bottom. 2 motor suspended individually adjustable in height and inclination. Permutation upper motor height with the mechanism of the upper clamp.
2 polishing disk Moulton 150 x 20 mm.
Nominate a support for the workpiece.
Electrical equipment of a modular control system for ease of service.
Permissible ambient temperature: min + 5 / max + 35 degrees Celsius.
With fluctuations in the mains voltage by more than +/- 10% on site required installation of voltage stabilizer.
All machines supplied in the member countries of the EU are manufactured in compliance with the requirements for safety in accordance with EU Directive for machines 98/37/EG Annex
2005 V.
One-sided edge banding machine in right hand versions to work on the glue melt.
Fining for work on the surface of the melt granules. Processing of granulated melt polyurethane adhesive is possible provided always complying with the requirements and recommendations of manufacturers of glue.
Supply of glue under glue roller.
Apply the adhesive to the part using an adhesive roller, rotating in the direction or against the direction of flow and does not require installation on the thickness of the workpiece. Electronic regulation of the temperature in the adhesive tank, with automatic temperature reduction in the adhesive tank when you stop work.
Contact heating Shoe to pre-heat the edges of the workpiece.
Auto shop for coiled and strip material, incl. device for cutting of the roll and the plate roll edge material with a diameter of 800 mm.
Area of a clip with a main pressure roller with pneumatic actuator and a pressing roller without drive.
Input range with 3 positions for jointing: 1,- 2,- or 3 mm.
Central adjustable mechanism of the upper clamp, and Central manual lubrication of the chain conveyor.
The control panel at the entrance to the machine.
PLANER – MILLING UNIT 2 X 2.2 KW
for pre-jointing unit before fining a part of, vertical reset through spindle, electro – pneumatic control in the horizontal plane, 2 motor 200 Hz, (1 motor operates in the direction of flow, 1 against), max allowance for the processing of 3 mm.
Set of 2 diamond milling head 100 x 48 x 30 mm, Z = 3 +3, maximum workpiece thickness 42 mm.
END TRIMMING UNIT CHAMFER / STRAIGHT
for trimming the front and rear overhangs the edge with pulling compound miter cut for high precision.
The angle of tilt 0 to 15 degrees, 2 motor 0.18 kW, 200 Hz, 12000 rpm Equipped with 2 crosscut saws ø 100 x 32 x 2.6 mm, Z = 30.
MILLING UNIT 2 X 0,27 KW, 0 – 15 DEGREES.
for milling the upper and lower overhangs the edge against the direction of flow. 2 motors are arranged one after the other, with vertical and horizontal feeling. Permutation upper motor height with the mechanism of the upper clamp. Digital signs for quick changes.
The edge material thickness 3 mm max.
Workpiece thickness 8 – 50 mm
The angle of tilt 0 to 15 degrees
Standard two combined indexable insert diameter 56/50 x 12 x 16 mm, Z = 4, R=3.
SCRAPING UNIT
Feeling top, bottom and side. Chamfer or fillet pre-milled PVC edges. The maximum thickness of the edge material 3 mm. Permutation upper device height mechanism with the upper clamp. Set of 2 profile knife R = 3 mm.
BUFFING UNIT WITH 2 MOTORS ON 0,09 KW
to soften the edges of the top and bottom. 2 motor suspended individually adjustable in height and inclination. Permutation upper motor height with the mechanism of the upper clamp.
2 polishing disk Moulton 150 x 20 mm.
Nominate a support for the workpiece.
Electrical equipment of a modular control system for ease of service.
Permissible ambient temperature: min + 5 / max + 35 degrees Celsius.
With fluctuations in the mains voltage by more than +/- 10% on site required installation of voltage stabilizer.
All machines supplied in the member countries of the EU are manufactured in compliance with the requirements for safety in accordance with EU Directive for machines 98/37/EG Annex
