Intelligent charger for Ni-Cd / Ni-Mh and Li-Ion battery.

This device allows independently from each other to charge, test, and determine the internal resistance from one to four Ni-Cd, Ni-MH and Li-Ion batteries, format AA, AAA, C, 26650, 22650, 18650, 17670, 18500, 18350, 17500, 17335, 14500, 16340, 10440 etc. to be unprotected and protection Board - almost similar to him Opus BT C3100.

- 4 independent channels to charge, discharge and test the battery.
- Install battery length 72mm (including pay protection)
Display with switchable backlight.
- Definition of faulty battery. If inserted in the charger the battery is damaged, the LCD displays "null ".
- Charging method for Li-ion batteries:
charge constant current (CC) and constant voltage (CV), charge method recommended high speed, saves the life of batteries and reduce their capacity over time.
- Automatic detection of the process end of the charge by the voltage drop (-dV) for Ni-Cd / Ni-Mh batteries
- Adjustable charge current: 300, 500, 700, 1000mA
- Discharge current: 250, 500mA
Testing internal resistance of batteries.
- Program "NOR TEST" to determine the actual capacity of the battery.
- The "FAST TEST" to eliminate "memory effect" with Ni-Cd and Ni-MH
batteries.
- Display the LCD-display of information about the real battery voltage (V) charging time (h) charge current (mA), capacity (mAh) and internal resistance (mOm).
- Contact in each slot is spring loaded, allowing you to charge various types of batteries.
- USB output to charge mobile devices lithium-Ion batteries.
- Power source – 12V.

The device has three modes of operation: CHARGE, FAST TEST and the NOR TEST.
After you install the battery, prompts the user for 8 seconds. use the MODE button to select the desired mode, and click CURRENT to set the optimal current.
If you take no action after installation of the batteries, the charger, the default mode is CHARGE (CHARGE) current
500mA.

Mode CHARGE (CHARGE).

The CHARGE of the battery.
Install the battery, observing correct polarity (positive terminal towards the display). Within 3 sec. will be determined by the internal resistance of the battery, its voltage and will be offered a choice of charging current. A short press of the button CURRENT select 300-500-700-100 0mA.
If within 8 seconds, the choice was not made - included a charge current of 500mA. On the LCD display during charging will display a "filled" capacity.

The FAST TEST (RAPID TEST)

The DISCHARGE-CHARGE the battery.
This mode is designed to eliminate "memory effect" with Ni-Cd and Ni-MH batteries. The charger first discharges the battery completely and then charging it again. In this case the display will show the capacity,
calculated during the total battery charge.
Install the battery and press the MODE button to select this mode.
The CURRENT button will set the desired charge current.
When you select charge current:
300 or 500mA - discharge current will be 250mA
700 or 1000mA - discharge current will be 500mA

Mode NOR TEST (STANDARD TEST)
CHARGE-DISCHARGE-CHARGE the battery.
This mode is intended to determine the actual capacity of the battery during its discharge. The charger fully charges the battery then discharges and then charges it again. In this case the display shows the capacity that is calculated during discharge of battery.
Install the battery and press the MODE button to select this mode.
The CURRENT button will set the desired charge current.
After the DISCHARGE cycle, the display will show a flashing icon END. This means that the real capacity of the battery has already been defined, but the device is still
operation CHARGE. After a full charge the battery icon END will be lit without blinking.

Mode USB (Powerbank)
Install charged Li-ion batteries in any charging slot. Connect
mobile device to the USB port, it automatically starts the charge process.
USB output it can supply current up to 1A.

Package contents:
- Memory
- BP
- Manual