Pumps console TO, km, new from the factory on the frame with the motor in the presence of a Kharkov pump For all models

Cantilever pumps with gland packing with electric motor fitted with wet rotor and secure the stator with two o-rings.

Pumps — centrifugal cantilever pumps based on the body. They are horizontal single stage with axial inlet fluid to the working wheel. Are designed for pumping fresh water with neutral pH 6-9, temperature 0 to 85° C and density, viscosity and chemical activity and containing solid inclusions on less than 0.1% and with a size of 0.2 mm. the Pumps are used in systems the municipal water supply. Not allowed installation and operation pumps in explosive and fire hazardous processes and use them to pumping of combustible and flammable liquids, as well as placement in residential buildings. Purpose and technical characteristics of pump parts type K and KM same, the pump units type KM have smaller overall the size and weight.

Pump To the torque from the shaft of the motor is applied to the shaft pump through flexible coupling. And KM pumps the impeller is installed on the end of the extended motor shaft.

Basically, the material of the parts all flow part cantilever pumps is cast iron.

The purpose of the pumps type "K" and "KM" diverse: they are used for pumping water and other neutral liquids, the temperature of which ranges from 0° C to 85° C. a solid content inclusions (size not more than 0.2 mm) with a volume concentration up to 0.1%.

In contrast to pumps of type "K", monoblock pumps"KM", there is one drawback - replacement of standard the motor unit lower power required after the grinding work wheel, difficult: requires some additional technical operations. Cantilever pumps K and KM are designed for pumping, in stationary pure water (except sea) and other liquids similar to clean water density, viscosity and chemical activity.

The design of the pump

Centrifugal single-stage pumps with one-side supply fluid to the impeller.

execution console pumps K, KM

1) Pumps - horizontal cantilever - where the torque from the shaft the motor is supplied to the pump shaft via flexible coupling.;

2) Pumps KM - cantilever monoblock pumps, where the impeller is set at the end of the motor extention shaft.

Material version of the pump The wet parts: cast iron brand CI20.

Shaft seal oil Seal a soft gasket or edge (single).

The pump casing is casting iron, which made the input and outlet nozzles, spiral-ring elbow and the pads.

The inlet is located on the axis of rotation, the outlet is directed vertically upward and is in one plane with the axis of rotation. To the body the pump is attached to the flange of the bracket. The bracket is connected to the seal housing screws. The seal housing is provided with holes for supplying cooling (packing) liquid to the stuffing box seal.

The impeller pump type - centrifugal, single-entry the closed type. Supply fluid to the impeller axis. The impeller unloaded from the action of axial force on the pump with a nominal diameter of impeller 200 - 315mm discharge openings executed on the main drive wheels, and on pumps with a nominal diameter of impeller 160mm a – impeller made on the main drive wheels.

The pump rotor is driven in rotation by an electric motor through a connecting bushing-finger clutch. The rotor support is ensured by two radial – thrust bearing mounted in the bracket. The direction of rotation of the rotor by a clockwise direction when viewed from the drive side.

Pumped medium:

Process water, except marine, and also other liquids similar to water density, viscosity and chemical activity with pH = 6:9 content solid particles not more than 1% by mass and not larger than 0.2 mm.

Marking:

For example:

C-50-200 U3.1 THE 3631-096-05747979-97

where - cantilever;

80 - diameter of inlet, mm;

50 - diameter of the outlet pipe, mm;

200 - diameter of the impeller (conventional), mm;

U3.1 - climatic version and placement category.

At the time of delivery of the pump with one of variants of working of wheels the outside diameter is added to the index:

"m" is increased diameter; "a", "b" a reduced diameter.

Our company is official representatives of the dealerships having a large number renowned manufacturers of pumping equipment and zapchastey to them, and - JSC "Pinsk OMZ" Belarus (pumps and units CNSM, Central nervous system, CNSG, Cnsk, ANS, CNS 105, CNS 60, 130 ANS, DS-125, DS, DS-134); OOO "Atomenergomash" (downhole (submersible) pumps ECV 5, 6 ECV, ECV 8, 10 ECV, ECV 12) Ukraine; OJSC "Livgidromash" (pumps and pumping units the basis of the D, 1D, VK, VKS, VKO, W, NMSH, SCN, SVN, SRL) Russia, JSC "kataysky pumping plant (